Voron Config

• Architecture: STM32
• Model: STM32G0B1
• Deployment Application: Yes
• Clock: 8 MHz
• Interface: CAN Bus on PB0/PB1
• App. Start Offset: 8KiB
• CAN Bus Speed: 1000000

Firmware Config is based on Klippain with machine specific overrides.

######################################################### \ #### User MCU and TMCs wiring definition file ########### + –> Everything MCU related :) ######################################################### /

# This file is yours: keep in mind that it will not be erased when updating # the config using moonraker and it will be kept as you've set it.

# Put here all your wiring definitions, your MCU serial port, CANbus UUID, etc… # It should be populated automatically with some default wiring templates during # the first time install of the config if you choose to do so when asked by the # script. If it's not the case, you will need to manually define all your # [board_pins] section. You can use the pinout documentation here: ./docs/pinout.md

# ——————————————————————————————

#————————-# # TMCs DRIVERS # #————————-#

# ———————————————————————- AXIS DRIVERS —→ optional, but only one line per axis need to be selected ### 1. X Drivers ————————————————————————- [include config/hardware/axis/X/TMC/TMC2209.cfg] # [include config/hardware/axis/X/TMC/TMC2209_V0specific.cfg] # Should only be used for early LDO V0 kits to mitigate the known VFAs issue # [include config/hardware/axis/X/TMC/TMC2240.cfg] # [include config/hardware/axis/X/TMC/TMC5160.cfg] ### 2. Y Drivers ————————————————————————- [include config/hardware/axis/Y/TMC/TMC2209.cfg] # [include config/hardware/axis/Y/TMC/TMC2209_V0specific.cfg] # Should only be used for early LDO V0 kits to mitigate the known VFAs issue # [include config/hardware/axis/Y/TMC/TMC2240.cfg] # [include config/hardware/axis/Y/TMC/TMC5160.cfg] ### 3. Z Drivers ————————————————————————- [include config/hardware/axis/Z/TMC/TMC2209_1-Motor.cfg] # [include config/hardware/axis/Z/TMC/TMC2209_3-Motors.cfg] # [include config/hardware/axis/Z/TMC/TMC2209_4-Motors.cfg] # [include config/hardware/axis/Z/TMC/TMC2240_1-Motor.cfg] # [include config/hardware/axis/Z/TMC/TMC2240_3-Motors.cfg] # [include config/hardware/axis/Z/TMC/TMC2240_4-Motors.cfg] # [include config/hardware/axis/Z/TMC/TMC5160_1-Motor.cfg] # [include config/hardware/axis/Z/TMC/TMC5160_3-Motors.cfg] # [include config/hardware/axis/Z/TMC/TMC5160_4-Motors.cfg] # —————————————————————————————-

# ——————————————————————- EXTRUDER DRIVER —→ optional, but only one line need to be selected ### ————————————————————————————– [include config/hardware/extruder/TMC/TMC2209.cfg] # [include config/hardware/extruder/TMC/TMC2240.cfg] # —————————————————————————————-

#———————————————# #### Fysetc Catalyst v1.x MCU definition ###### #———————————————#

[mcu] ##——————————————————————– # This board work by using a serial connection by default. If you # want to use CAN, invert the commented lines and use canbus_uuid.

serial: /dev/serial/by-id/usb-Klipper_stm32f401xc_100046001851383531393138-if00 # canbus_uuid: change-me-to-the-correct-canbus-id ##——————————————————————–

[include config/mcu_definitions/main/Fysetc_Catalyst_v1.x.cfg] # Do not remove this line [board_pins catalyst_mcu] mcu: mcu aliases:

  X_STEP=MCU_B_MOT_STEP    , X_DIR=MCU_B_MOT_DIR    , X_ENABLE=MCU_B_MOT_ENABLE    , X_TMCUART=MCU_B_MOT_CS_PDN    ,
  Y_STEP=MCU_A_MOT_STEP    , Y_DIR=MCU_A_MOT_DIR    , Y_ENABLE=MCU_A_MOT_ENABLE    , Y_TMCUART=MCU_A_MOT_CS_PDN    ,
  Z_STEP=MCU_Z_MOT_STEP    , Z_DIR=MCU_Z_MOT_DIR    , Z_ENABLE=MCU_Z_MOT_ENABLE    , Z_TMCUART=MCU_Z_MOT_CS_PDN    ,
  E_STEP=MCU_E_MOT_STEP    , E_DIR=MCU_E_MOT_DIR    , E_ENABLE=MCU_E_MOT_ENABLE    , E_TMCUART=MCU_E_MOT_CS_PDN    ,
  X_STOP=MCU_B_MOD_DIAG, Y_STOP=MCU_A_MOD_DIAG, Z_STOP=PA3,
  #X_STOP=tmc2209_stepper_x:virtual_endstop, Y_STOP=tmc2209_stepper_y:virtual_endstop,
  DRIVER_SPI_MOSI=MCU_SPI_MOSI , # Used in case of SPI drivers such as TMC2240 or TMC5160
  DRIVER_SPI_MISO=MCU_SPI_MISO , # Used in case of SPI drivers such as TMC2240 or TMC5160
  DRIVER_SPI_SCK=MCU_SPI_SCK   , # Used in case of SPI drivers such as TMC2240 or TMC5160
  
  PROBE_INPUT=MCU_PROBE   ,
  RUNOUT_SENSOR=MCU_IO2,
  E_HEATER=MCU_HEAT     , E_TEMPERATURE=MCU_T0   ,
  BED_HEATER=MCU_BED , BED_TEMPERATURE=MCU_T1 ,

  PART_FAN=MCU_FAN1 , E_FAN=MCU_FAN0 ,
  CONTROLLER_FAN=MCU_FAN2        ,

  LIGHT_NEOPIXEL=MCU_NEOPIXEL      ,